Install

Permalink Gallery

Eurosens Degree Bt tilt angle sensor connection to Teltonika FMBXXX

Eurosens Degree Bt tilt angle sensor connection to Teltonika FMBXXX

Wireless tilt angle sensor Eurosens Degree BT has different operation modes. Lets see how it is connected to the popular GPS trackers Teltonika FMB XXX in the modes : tilt angle monitoring and events detection, concrete mixer truck monitoring, boom monitoring. (more…)

Permalink Gallery

Eurosens Dominator Bt connection to the Smart GPS (Navtelecom) over Bluetooth BLE

Fuel theft alarm
Permalink Fuel theft alarmGallery

Instant fuel theft alarm with Eurosens Dominator fuel level sensors

Eurosens Dash
Permalink Eurosens DashGallery

Setting up the Eurosens Dash controller

Setting up the Eurosens Dash controller

Eurosens Dash resistive fuel level sensor emilator is designed to control the fuel gauge on the dashboard. Eurosens Dash reads the fuel level (volume) value via the RS-485 interface and the LLS protocol. (more…)

Permalink Gallery

Eurosens Dominator Bt connection to the GalileoSky GPS over Bluetooth BLE

Eurosens Dominator Bt connection to the GalileoSky GPS over Bluetooth BLE

Терминалы Galileosky  имеют встроенный модуль Bluetooth BLE, который обеспечивает считывание данных с беспроводных Bluetooth-датчиков. Рассмотрим подключение датчиков уровня топлива Eurosens Dominator Bt (more…)

Permalink Gallery

Eurosens Dominator Bt connection to the Smart GPS (Navtelecom) over Bluetooth BLE

Eurosens Dominator Bt connection to the Smart GPS (Navtelecom) over Bluetooth BLE

Popular GPS trackers Smart produced by Navtelecom company has built-in Bluetooth module. It can read the data from wireless Bluetooth sensors. Here is how to connect wireless fuel level sensor Eurosens Dominator Bt to the Smart GPS tracker. (more…)

Permalink Gallery

How to connect eurosens fuel level sensors and fuel flowmeters to Galileosky 7.0x via MODBUS (RS485)

,

How to connect eurosens fuel level sensors and fuel flowmeters to Galileosky 7.0x via MODBUS (RS485)

,

It may be challenging to add completely different sensor types (a fuel level sensor and a fuel flowmeter) to one RS 485 interface of a GPS tracking device. The reason is the different data exchange protocol that corresponds to different sensor types. However, there is no such problem if we use the universal MODBUS protocol.

This article will explain how to connect Eurosens Dominator RS fuel level sensor and Eurosens Delta RS fuel flowmeter to Galileosky 7.0x GPS tracker.
(more…)

Permalink Gallery

Fuel level monitoring : tank calibration tricks and tips from Mechatronics

Fuel level monitoring : tank calibration tricks and tips from Mechatronics

Fuel level sensors are very popular tools of fuel consumption monitoring it GPS tracking industry. Very important stages of its installation – sensor calibration and tank calibration. Every installer wants to make installation process as simple as possible. This article could help you to cut installation time or avoid calibration errors. (more…)

Permalink Gallery

Fuel consumption monitoring: the comprehensive guide from Mechatronics

, ,

Fuel consumption monitoring: the comprehensive guide from Mechatronics

, ,

Fuel consumption monitoring is an important feature of GPS tracking and fleet management. There are several ways to measure vehicle’s real fuel consumption, the most common are the following ones: (more…)

Permalink Gallery

Onboard weighing system : installation and integration

Onboard weighing system : installation and integration

Onboard weighing system is a highly demanded option among GPS tracking provides as the system helps to avoid heavy fines for overload, prevent cargo theft and unauthorized fleet usage. (more…)

Permalink Gallery

Using fuel consumption meters to calculate fuel volume in the tank : Wialon-Application

Using fuel consumption meters to calculate fuel volume in the tank : Wialon-Application

A fuel consumption sensor is often installed in the tank, while the remaining fuel in the tank is not measured. The new software module for Wialon allows you to calculate the volume of the remaining fuel in the tank. (more…)

Permalink Gallery

How to use the MODBUS interface to connect Eurosens Delta fuel meter, Display RS and GPS tracker

, ,

How to use the MODBUS interface to connect Eurosens Delta fuel meter, Display RS and GPS tracker

, ,

We are going to connect the fuel consumption meter Eurosens Delta RS, onboard display Eurosens Display RS and GPS tracker Smart 2435 (Navtelecom) using RS485 interface, MODBUS protocol. (more…)

Permalink Gallery

How to connect 2 fuel level sensors to the onboard display and GPS tracker

,

How to connect 2 fuel level sensors to the onboard display and GPS tracker

,

We will use 2 fuel level sensors Eurosens Dominator RS, onboard display Eurosens Display RS and GPS tracker SMART 2435 from Navtelecom. (more…)

Permalink Gallery

Fuel consumption meter and fuel level sensor data comparison: Wialon-Application

, ,

Fuel consumption meter and fuel level sensor data comparison: Wialon-Application

, ,

Provided we have both fuel consumption sensor and a fuel level sensor installed. The new software module for wialon allows you to quickly compare their data on a single graph, detect unauthorized drains and quickly diagnose the operation of the equipment.
(more…)

Permalink Gallery

How to connect Eurosens DDS CAN axle load sensor to GPS tracker using CAN-bus interface

How to connect Eurosens DDS CAN axle load sensor to GPS tracker using CAN-bus interface

 

Comparing to axle load sensors with analog output (DDS A, earlier – Difference 02), digital axle load sensor Eurosens DDS CAN have several advantages: (more…)

Permalink Gallery

(Русский) Телеграм-бот подбора расходомера на двигатели

,

Permalink Gallery

Fuel consumption meters – table of analogues

,

Fuel consumption meters – table of analogues

,

This table will help you to choose an equivalent flow meter model amoung three different manufacturers : Mechatronics, Technoton and Aquametro. You can save some money with it! (more…)

RS-485 over air
Permalink RS-485 over airGallery

Wireless RS485 connection (for truck+trailer case)

,

Wireless RS485 connection (for truck+trailer case)

,

Sometimes it is necessary to transmit RS485 over an air, for example to get data from fuel level sensors installed in the trailer to GPS tracker installed in the truck. In this case we can use Eurosens Datalink wireless bridge. It is a pair of 433 Hz radiomodules with RS485 interface with LLS protocol support. (more…)

Display подача обратка modbus
Permalink Display подача обратка modbusGallery

Eurosens Display + 2xEurosens Direct + RS485 Modbus GPS tracker

,

fuel level sensor + display + gps
Permalink fuel level sensor + display + gpsGallery

Using Eurosens Display to add fuel data from several tanks + GPS tracker

,

Using Eurosens Display to add fuel data from several tanks + GPS tracker

,

Using Eurosens Display and several fuel level sensors to show total fuel volume in the tanks.

(more…)

several tanks fuel volume total
Permalink several tanks fuel volume totalGallery

Using Eurosens Display to sum fuel data from several tanks

,

Using Eurosens Display to sum fuel data from several tanks

,

Using Eurosens Display and several fuel level sensors to show total fuel volume in the tanks.

(more…)

Permalink Gallery

Setting up the “Waste truck weighing” Wialon App

Setting up the “Waste truck weighing” Wialon App

How to connect “Dump truck weighing” Wialon application
(more…)

Weighing Wialon App
Permalink Weighing Wialon AppGallery

Setting up the “Dump truck weighing” Wialon App

Setting up the “Dump truck weighing” Wialon App

How to connect “Dump truck weighing” Wialon application
(more…)

Permalink Gallery

Waste truck onboard weighing Wialon App

Waste truck onboard weighing Wialon App

This Wialon Application allows you to determine the weight of garbage transported by a garbage truck
(more…)

Fuel level sensor Eurosens Dominator
Permalink Fuel level sensor Eurosens DominatorGallery

Why digital interface (CAN bus, RS232/RS485) is preferable for the fuel level sensor connection

Why digital interface (CAN bus, RS232/RS485) is preferable for the fuel level sensor connection

If your GPS-tracker allows you to connect the fuel level sensor via the digital RS485 / RS232 / CAN interface – it should be preferred to the analog or frequency input. There are following reasons: (more…)

CAN bus fuel consumption data
Permalink CAN bus fuel consumption dataGallery

Why digital interface (CAN bus, RS232/RS485) is preferable for the fuel consumption meter connection

,

Why digital interface (CAN bus, RS232/RS485) is preferable for the fuel consumption meter connection

,

 

You should prefer digital interface between GPS tracker and fuel consumption meter. And there are several reasons for it (more…)

Отчет о ходках вес груза
Permalink Отчет о ходках вес грузаGallery

Eurosens Difference Wialon Application

Eurosens Difference Wialon Application

Wialon Application which is used for cargo weight trips reporting. (more…)

Fuel level sensor calibration - full
Permalink Fuel level sensor calibration - fullGallery

How to calibrate Eurosens Dominator sensor and fuel tank with a help of Eurosens Display

,

How to calibrate Eurosens Dominator sensor and fuel tank with a help of Eurosens Display

,

This is a simplified method to calibrate fuel level sensors Eurosens Dominator without laptop and Eurosens Configurator software. Instead of laptop we will use Eurosens Display RS. (more…)

Permalink Gallery

Compatibility of Eurosens sensors with GPS trackers and data terminals

, , ,

Compatibility of Eurosens sensors with GPS trackers and data terminals

, , ,

This list is big but not complete. Analog interface can be used in the most cases but there are some disadvantages. We recommend to use digital interfaces as first choice : CAN bus or serial (RS232/RS485/K-line). (more…)

Пломбировка датчика уровня топлива
Permalink Пломбировка датчика уровня топливаGallery

Sealing of Eurosens Dominator fuel level sensors

Sealing of Eurosens Dominator fuel level sensors

Convenient and reliable sealing of fuel level sensors for their installation and maintenance. How is this done? (more…)

Fuel level sensor Eurosens Dominator
Permalink Fuel level sensor Eurosens DominatorGallery

The reasons of Eurosens Dominator design

The reasons of Eurosens Dominator design

We believe that the GPS tracking system should work for many years (for example, the warranty period for the Eurosens Dominator fuel level sensors is set at 5 years) and still continue to work after the end of the warranty. (more…)

Датчик уровня топлива ГЛОНАСС
Permalink Датчик уровня топлива ГЛОНАССGallery

Compatibility of Eurosens level sensors vs GPS trackers

Compatibility of Eurosens level sensors vs GPS trackers

We recommend to use digital interfaces for fuel level sensor connection – RS232, RS485.

Fuel level sensors Eurosens Dominator RS can be connected to GPS trachers with RS232 and RS485 interface.
List of compatible GPS trackers.

(more…)

Summator inside Dominator RS
Permalink Summator inside Dominator RSGallery

Dominator Network

Dominator Network

Summator inside Eurosens Dominator RS.

Permalink Gallery

Cable pinout

Cable pinout

Socket (female). According DIN 72585 / ISO 15170.

Permalink Gallery

Display-Delta

Display-Delta

Connection Eurosens Delta flowmeters to the fuel indicator Eurosens Display F1.

Permalink Gallery

Display-Dominator

,

Display-Dominator

,

Connection level sensors Eurosens Dominator to the fuel indicator Eurosens Display F1.

Permalink Gallery

Eurosens Delta install scheme 1

Eurosens Delta install scheme 1

Installation Eurosens Delta (all modifications) on sucction side.
Designations on the scheme:
1 – backpressure valve
2 – additional filter of thin cleaning
3 – pressuure valve

Permalink Gallery

Cutting the Eurosens Dominator sensor

Cutting the Eurosens Dominator sensor

Cutting of electrodes at installation. Designations on the scheme: 1 – fuel tank 2 – fuel h2 – possible dirt or water L – initial length L1 – the recommended cutting length When installing the bottom stop, the distance from the bottom end of the electrodes to the bottom of the tank should be approximately 30 mm. In the absence of a bottom stop: 10-15mm. When the bottom stop is installed, the sensor should protrude beyond the upper plane of the tank by about 15 mm after immersion in the tank . In the absence of the bottom stop, the sensor should be completely lowered onto the bayonet plate without touching the bottom of the tank.